收藏本站
DS28EC20: 20Kb 1-Wire EEPROM
ADDRESS REGISTERS AND TRANSFER STATUS
The DS28EC20 employs three address registers: TA1, TA2, and E/S (Figure 6). Registers TA1 and TA2 must be
loaded with the target address to which the data is written or from which data is read. Register E/S is a read-only
transfer status register used to verify data integrity with write commands. E/S bits E[4:0] are loaded with the
incoming T[4:0] on a Write Scratchpad command and increment on each subsequent data byte. This is, in effect, a
byte-ending offset counter within the 32-byte scratchpad. Bit 5 of the E/S register, called PF, is set if the number of
data bits sent by the master is not an integer multiple of 8 or if the data in the scratchpad is not valid due to a loss
of power. A valid write to the scratchpad clears the PF bit. Bit 6 has no function; it always reads 0. The highest
valued bit of the E/S register, called authorization accepted (AA), is valid only if the PF flag reads 0. If PF is 0 and
AA is 1, the data stored in the scratchpad has already been copied to the target memory address. Writing data to
the scratchpad clears this flag.
Figure 6. Address Registers
Bit #
Target Address (TA1)
Target Address (TA2)
Ending Address with
Data Status (E/S)
(Read Only)
7
T7
T15
AA
6
T6
T14
0
5
T5
T13
PF
4
T4
T12
E4
3
T3
T11
E3
2
T2
T10
E2
1
T1
T9
E1
0
T0
T8
E0
WRITING WITH VERIFICATION
To write data to the DS28EC20, the scratchpad must be used as intermediate storage. First, the master issues the
Write Scratchpad command to specify the desired target address, followed by the data to be written to the
scratchpad. Under certain conditions (see the Write Scratchpad Command section) the master receives an inverted
CRC16 of the command, address (actual address sent), and data at the end of the Write Scratchpad command
sequence. Knowing this CRC value, the master can compare it to the value it has calculated itself to decide if the
communication was successful and precede to the Copy Scratchpad command. If the master could not receive the
CRC16, it should send the Read Scratchpad command to verify data integrity. As a preamble to the scratchpad
data, the DS28EC20 repeats the target address TA1 and TA2 and sends the contents of the E/S register. If the PF
flag is set, data did not arrive correctly in the scratchpad or there was a loss of power since data was last written to
the scratchpad. The master does not need to continue reading; it can start a new trial to write data to the
scratchpad. Similarly, a set AA flag together with a cleared PF flag indicates that the device did not recognize the
Write command. If everything went correctly, both flags are cleared and the ending offset indicates the address of
the last byte written to the scratchpad. Now the master can continue reading and verifying every data byte. After
the master has verified the data, it can send the Copy Scratchpad command, for example. This command must be
followed exactly by the data of the three address registers TA1, TA2, and E/S. The master should obtain the
contents of these registers by reading the scratchpad. As soon as the DS28EC20 has received these bytes
correctly, it starts copying the scratchpad data to the requested location, provided that the target memory is not
copy protected, the PF flag is cleared, and there was no Read Memory or Extended Read Memory command
issued between Write Scratchpad and Copy Scratchpad.
10 of 27
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DS301X KWIK-CHG DESIGNATION STRIP SGL
DS3030W-100# IC NVSRAM 256KBIT 100NS 256BGA
DS3045W-100# IC NVSRAM 1MBIT 100NS 256BGA
DS3050W-100# IC NVSRAM 4MBIT 100NS 256BGA
DS3065W-100# IC NVSRAM 8MBIT 100NS 256BGA
DS3065WP-100IND+ IC SRAM 3.3V 8MB 34POWERCAP MOD
DS3070W-100# IC NVSRAM 16MBIT 100NS 256BGA
DS321X KIT X-WIDE DESIGN STRIP VERT
相关代理商/技术参数
DS28EC20-224-BB+ 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
DS28EC20P 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DS28EC20_1203
DS28EC20P T 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:DS28EC20_1203
DS28EC20P+ 功能描述:电可擦除可编程只读存储器 20Kb 1-Wire 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
DS28EC20P+T 功能描述:电可擦除可编程只读存储器 20Kb 1-Wire 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
DS28EC20P-224-BB+T 制造商:Maxim Integrated Products 功能描述:- Tape and Reel
DS28EC20Q-A5A-5A+T 制造商:Maxim Integrated Products 功能描述:20KB 1-WIRE EEPROM - Tape and Reel
DS28EC20Q-A5A-5A+W 制造商:Maxim Integrated Products 功能描述:20KB 1-WIRE EEPROM - Rail/Tube